INDUCTIVE RPM PICKUP
This sensor picks up Engine RPM from the ignition coil on a magneto ignition and transmits it via 2- or 3-pin Molex cable connection
PDS & Racepak Sensors for Data Acquisition
Accurate data starts with accurate measurement. PDS offers sensors for monitoring the critical variables behind race car performance, including pressure, temperature, RPM, position, fuel flow, and vehicle dynamics. We also support Racepak sensors and legacy applications, helping racers maintain and expand existing data acquisition systems.
Save 0%
This sensor picks up Engine RPM from the ignition coil on a magneto ignition and transmits it via 2- or 3-pin Molex cable connection
Save 0%
The Series II transducer modules provide a variety of inputs from pressure and temperature, to voltage and strain gauge readings.
Save 0%
These pressure sensors work with XBus and V-Net pressure modules, USM modules and Pro modules. Available in 75, 100, 150, 200, 250, 300 and 500 psi.
Save 0%
This exposed tip Type-K thermocouple reacts quickly to changing temperatures in manifold plenum or the clutch bellhousing. Must be used with the ap...
View full details
Save 0%
This crank trigger picks up the magnets in the degree wheel and can also be used as a TDC sensor to determine the actual ignition timing of the eng...
View full details
Save 0%
PDS' own brand of linear travel sensors are designed to monitor shock travel or similar positions such as throttle or clutch. Features: Linear Tra...
View full details
Save 0%
2-pin mil-spec flow meter connector kit. Includes connector, locking mechanism and heatshrink.
Save 0%
This rod end compression load cell detects pressure on the wheelie bar, indicating when it makes contact with the racing surface. It features a 1/2...
View full details
Save 0%
Exhaust Gas Temperature is a critical indicator of the performance of a typical racing engine. Supercharged and turbocharged engines use EGT sensor...
View full details
Save 0%
Two piece adapter fitting to adapt 3/16” thermocouple probe to 1/8 NPT.
Save 0%
This remotely-mounted accelerometer can measure acceleration, lateral or vertical G-forces, depending on mounting. Requires either a 3-pin cable or...
View full details
Save 0%
This sensor sources the ignition pulses directly from the ignition control box, and then transfers the signals to the data logger using optic cable...
View full details
Save 0%
This pickup connects to the "Tach Output" on your MSD ignition and features a 3-pin Molex connector to connect to the RPM harness of a V300SD or V5...
View full details
Save 0%
Performance Data Systems' Wheelie Bar Load Cell is designed to be installed on the compression bar(s) of a wheelie bar on a drag racing vehicle. Th...
View full details
Save 0%
Full EGT coverage for alcohol and gas combinations in one box. This set of 8 thermocouple probes gives you per-cylinder exhaust gas temperature rea...
View full details
Save 0%
The FM-PICKUP is a replacement flow-meter pickup for supported motorsports flow-measurement systems.Confirm the flow-meter model and required PDS X...
View full details
Save 0%
This single-wire sensor is commonly used to pick up coolant or transmission temp for the IQ3 and UDX Street Dashes, as well as the LDX and UDX Repl...
View full details
Save 0%
0-600°F V-Net Manifold temperature and sensor. Comes with a 36" lead.
Sold out
PDS' own brand of linear travel sensors are designed to monitor shock travel or similar positions such as throttle or clutch. Features: Linear Tra...
View full details
Save 0%
Spring-loaded linear travel sensors are designed to monitor the release (throwout) bearing on clutches. Features: Clutch Linear Sensors - 3” and 4...
View full details
Save 0%
0-1.0” linear travel sensor, used to monitor throttle position. Also can be used to monitor fuel system slide valve movement.
Save 0%
Single channel Air/Fuel module, harness and sensor.
Save 0%
Exhaust Gas Temperature is a critical indicator of the performance of a typical racing engine. Supercharged and turbocharged engines use EGT sensor...
View full details
Save 0%
This crank trigger picks up the magnets in the degree wheel and can also be used as a TDC sensor to determine the actual ignition timing of the eng...
View full details